10GBASE-SR SFP+ 850nm 300M LC XFP moduel media converter transceiver

10GBASE-SR SFP+ 850nm 300M LC XFP Moduel Media Transceiver 0

10GBASE-SR SFP+ 850nm 300M LC XFP Moduel Media Transceiver 1

Features

1. 10Gb/s serial opticaal interface compliant to 802.3a ae 10GBASE-SR
2. Electrical interface compliant to SFF-8431 specifications for enhanced 8.5 and 10 Gigabit small form factor pluggable module “SFP+”
3. 850nm VCSEL tran nsmitter, PIN photo-detector
4. 2-wire interface for management specifications comp pliant with SFF 8472 digital diagnostic mmonitoring interface for optical transceiv vers
5. Operating case tem mperature: 0 to 70°C
6. All-metal housing foor superior EMI performance
7. Low power consum mption
8. Advanced firmware e allow customer system encryption information to be stored in transceive er
9. Cost effective SFP++ solution, enables higher port densitie ies and greater bandwidth
10. RoHS compliant

Applications

1. High-speed storage area networks
2. Computer cluster cross-connect
3. Custom high-speed data pipes
Inter Rack Connection

GENERAL DESCRIPTION

This 850 nm VCSEL 10Gigabit SFP+ transceiver is designed to transmit and receive optical data over 50/125 µm or 62.5/125 µm multimode optical fiber (Table 1).

The SFP+ SR module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.

The transmitter converts 10Gbit/s serial PECL or CML electrical data into serial optical data compliant with the 10GBASE-SR standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic “1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (Tx_Fault) is provided. TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 k . TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the SFP+ module transmitter output shall be turned

off. This contact shall be pulled up to VccT with a 4.7 k to 10 k resistor.

The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data. An open collector compatible Loss of Signal is provided. Rx_LOS when high indicates an optical signal level below that specified in the relevant standard. The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 k , or with an active termination. Power supply filtering is recommended for both the transmitter and receiver. The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP+ is installed that the received signal strength is below the specified range. Such an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.

Absolute Maximum Ratings

Parameter	Symbol	Min	Max	Unit
Supply Voltage	Vcc	0	3.6	V
Storage Temperature	Tc	-40	+85	℃
Operating Case Temperature	Tc	0	70	℃
Relative Humidity	RH	5	95	%
RX Input Average Power	Pmax	-	0	dBm

Recommended Operating Conditions

Parameter	Symbol	Min	Typical	Max	Unit
Power Supply Voltage	Vcc	3.135	3.3	3.465	V
Power Supply Current	lcc			250	mA
Operating Case Temperature	TC	0	25	70	℃

etiqueta:

Lugar de origem:	CHINA
Marca:	Neutral
Certificação:	CE, FCC, ROHS
Número do modelo:	OFSP-8510G-03L

Quantidade de ordem mínima:	2 PCes
Preço:	USD 8~9.5/PIECE
Detalhes da embalagem:	10 PCS/PACKET
Tempo de entrega:	5-10 dias, dependem da quantidade
Termos de pagamento:	L/C, T/T, Western Union, Paypal e assim por diante
Habilidade da fonte:	50000 PCes/mês

Dados-taxa:	10Gbase	Tipo da fibra:	Multi-modo duplo da fibra
Fonte de alimentação:	+3.6V	Comprimento de onda:	850nm
Distância de transmissão:	300m	Temperatura de caso de funcionamento:	0~70℃
Destacar:	LC XFP Moduel Media Transceiver , 300M XFP Moduel Media Transceiver , 850nm Media Converter Transceiver

	Shenzhen Optfocus Technology Co., Ltd.
	Pavimente 3, No.7 de construção, parque industrial de Tangtou ó, rua de Shiyan do distrito de BaoAn, cidade China de ShenZhen
	86-755-26511956
	jenny@optfocus.com

10GBASE-SR SFP+ 850nm 300M LC XFP Moduel Media Transceiver

LC XFP Moduel Media Transceiver

300M XFP Moduel Media Transceiver

850nm Media Converter Transceiver

Transceptor do Ethernet do gigabit

transceptor de fibra óptica

transceptor óptico da fibra